Vicon V962-N Guía de instalación

www.vicon-security.com XX224-10-08V960-N Series Network CamerasVicon Industries Inc. does not warrant th

3.3 Live View Client PC Speaker (enable/disable) Client PC Microphone (enable/disable) Digital Zoom Snapshot Full Screen Vide

H.264 Protocols & Communication Methods (continued) Unicasting is communication between a single sender and a single receiver over a network. This

4. Setup The V960-N is configured from the Setup tab, which is available on the upper-left hand side in the web interface. This configuration could

5. Installation The following descriptions show examples of some of the features available with V960-N. 5.1 Installation Mode Installation M

6. Video The following descriptions show examples of some of the features available with V960-N. 6.1 Video Codec This section allows you to ch

Using H.264, it is also possible to control the bit rate, which in turn allows the amount of bandwidth usage to be controlled. CBR (Constant Bit Rate)

Bandwidth Limit Limit the bandwidth that the V960-N can use during a network connection. Max Bandwidth Specify the maximum bandwidth that the V9

6.2 Camera This section allows you to adjust various camera settings. 6.2.1 Exposure Control Exposure Mode Select AUTO outdoor or indo

Max AGC Gain For low light conditions, select HIGH value; otherwise select LOW. DC -Iris Control Turn OFF the DC-Iris lens setting when focusing the

7. Audio The V960-N can transmit audio to other clients and can also play audio received from other clients. This section describes the basic audio

Contents 1. Product Features ... 3 2. Installation and Adj

8. Live The V960-N can support up to 10 simultaneous users via Unicast. With multicasting, V960-N can support an unlimited number of users. If s

9. SD Card 9.1 Configuration SD Card Configuration This configuration page allows you to save video and still images to the Micro SD (S

9.2 Event Event SD Writing You can configure the camera to store still images based on events such as Alarm In and Motion detection. NOTE:

SD Write Mapping Choose which types of events (Alarm In or Motion) will be recorded to the SD card by checking the desired event. Effective Perio

10. FTP 10.1 Configuration Server Configuration Enable/Disable the FTP function to download saved content from the SD Card remotely. Wh

Event FTP Sending Allows transmission of still images to the FTP server at remote sites when an event occurs. NOTE: This function cannot be used

11. Event 11.1 Alarm Port Alarm Input Used for connecting external alarm contacts and triggering specific alarm-based events. The input is

11.2 Motion Motion Detection Motion detection is used to generate an alarm whenever movement occurs within the video image. A total of 4 moti

11.3 Mapping Event Mapping It is possible to define conditions that would cause the camera to respond with certain actions. A triggered event h

12. Network 12.1 IP Setup IP Address Configuration The V960-N supports both IP version 4 and IP version 6 (IPv6 will be supported as of

12. Network ... 28 12.1 IP Setup ...

How to Assign an IP Address Default setting is set to “DHCP” and “UPnP” function is set to ON. If your network has a DHCP server and the UPnP functi

12.2 Service Port Service Port HTTP Port The default HTTP port number (80) could be changed to any port within the valid port range (1-6553

12.3 RTP RTP Port Range The IP address, port numbers, and Time-To-Live (TTL) value are for use for the video stream(s) in Multicast H.264 fo

You must turn Notification to ‘ON’ and then enter the host names or addresses for your mail servers in the fields provided to enable the sending of

How to setup the DDNS: 1) DDNS set to ON. “mac address.dvrlink.net” is registered to the DDNS server. User can connect to the camera with: “

In order to be able to detect the camera automatically, you must enable the UPnP function on both the camera and on your PC. Camera : Set UPnP to “

13. System 13.1 User When you access the camera, the Configure Root Password dialog box appears. Enter the user name ADMIN and password 1

12.2 Date & Time Date & Time Format Specify the formats for the date and time (12h or 24h) displayed in the Live View video streams.

13.3 Maintenance System Name Choose a system name to identify the camera when using e-mail notifications. System Reboot Reboots the camera

1. Product Features The V960-N Series HD/Megapixel IP camera is a high performance H.264 network camera, designed for demanding security installat

4. If you suspect the firmware upgrade for the camera has failed, always wait at least 5-10 minutes before restarting the upgrade process. 5. Vico

13.4 Information System Information After updating firmware, you can confirm the new F/W version here.

Vicon Standard Equipment Warranty Vicon Industries Inc. (the “Company”) warrants your equipment to be free from defects in material and workmanship

Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-2288 800-645-9116 Fax: 631-951-2288 Vic

1. Alarm & Audio I/O (8-pin connection terminal): Audio in Audio in (line level), for line-in mono signal (only left channe

6. Power Connector 12VDC or 24VAC power connector 7. Status LED Indicator LED Color Indication System Status Status Green On Network conne

2. Installation and Adjustments 2.1 Mounting the Camera The camera provides mounting holes on the bottom and top; either hole can be used to mou

3. Accessing the Camera The V960-N can be accessed with most standard operating systems and browsers. The recommended browser is Internet Expl

NOTE: The layout of the live view page in the camera may have been customized to meet specific requirements. Consequently, some of the examples a