Vicon IX 2000 L Información técnica Pagina 137
- Pagina / 256
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MX Control Card Configuration
Vicon MX Hardware System Reference A-25
General Cautions and Access Instructions
Before touching anything inside the MX Control, use an earth strap
or touch a properly grounded point to dissipate static electricity.
Continue to wear an earth strap or periodically touch the earth point
whenever handling the PCBs inside the MX Control.
When you disconnect a cable, pull on its connector or on its strain-
relief loop, not on the cable itself. As you pull connectors apart, keep
them evenly aligned to avoid bending any pins. Also, before you
connect a cable, make sure both connectors are correctly aligned and
oriented.
Handle internal cards with care. Do not touch components or contacts
on a card. Hold a card by its edges or by its metal mounting bracket.
To gain access to the internal circuits of the MX Control:
1. Switch off the MX Control through the MX Ultranet or MX Net, or
remove the Lemo plug from the Net Connect socket on the rear
panel of the MX Control.
2. With an M3 Pozidrive™ screwdriver, undo and remove the screws:
six on the top and eight on each side of the cover.
3. Gently lift the top panel upwards and set it aside.
You can now replace the relevant MX option cards, as described in the
following sections.
Installing an MX Option Card
This section describes how to install an analog or audio ADC option
card in the Device 1 or Device 2 slot in the rear of the MX Control. If
you have installed an analog ADC option card, also see section
Connecting Analog ADC Devices via the Patch Panel on page A-27.
To install an MX option card in the MX Control board:
1. Remove blank panel covering the slot if the option card was not
factory installed, or remove an existing option card if you are
replacing it.
MXhardware_Reference.book Page 25 Monday, April 30, 2007 1:56 PM
- System Reference 1
- Vicon MX Hardware 1
- Contents 3
- Audience 9
- Structure 10
- Conventions 12
- Related documentation 13
- System Information 15
- MX Software 16
- MX Peripherals 16
- Third-Party Devices 16
- Environmental Regulations 17
- Safety Information 18
- Warranty 19
- CE Declaration of Conformity 20
- Introduction 23
- Vicon MX Architecture Models 25
- MX Bridge 29
- MX Bridge Rear Panel 31
- Supported Camera Modes 32
- MCam2 Cameras 33
- 14 for VCam/SVCam cameras 34
- Camera Select dial 35
- Camera Select 35
- MX Cameras 37
- Camera Lenses 39
- Field of View 40
- Figure 3-4: Image circle 42
- Aperture and Depth of Field 44
- Camera Lens Filters 44
- MX Camera Rear Panels 46
- Camera Lens Mount 49
- Tripod Mount 49
- Camera Strobe Units 50
- Strobe Unit Connections 51
- Strobe Unit Status Indicators 51
- Unassigned 53
- MX Control 55
- MX Control Rear Panel 58
- MX Host PC 67
- Ethernet Port on Host PC 68
- Vicon Software on Host PC 69
- Movie Capture Card on Host PC 70
- MX Link Front Panel 73
- MX Link Rear Panel 74
- MX Net Front Panel 77
- MX Net Rear Panel 79
- MX Sync Front Panel 81
- MX Sync Rear Panel 82
- MX Ultranet 85
- MX Ultranet Front Panel 86
- MX Ultranet Rear Panel 87
- MX Accessory Kit 93
- MX Cable Descriptions 97
- MX Cables 100
- Vicon Cameras 101
- MX Hardware Units 101
- MX Cable Order Information 102
- MX Calibration Kit 103
- Calibration Kit Contents 104
- MX Control Card Configuration 113
- Timecode and Genlock Option 114
- Ω (ohms) 114
- MX Control Standard Card 115
- Important 117
- Installing MX Option Cards 136
- Installing an MX Option Card 137
- Figure A-6: Vicon patch panel 139
- Figure A-7: 100-way cable 140
- Figure A-8: ADC edge socket 140
- GPIO and Remote Connections 141
- Electrical Specifications 142
- GPIO Functionality 144
- Custom GPO Programming 145
- GPO File Format 146
- GPO File Structure 146
- XML Header 149
- AllPrograms section 149
- GPO File Attribute Syntax 149
- Program Name Section 150
- Type Section 150
- Polarity Section 151
- StartEvent Section 151
- StopEvent Section 152
- StartOffset Section 152
- StopOffset Section 153
- PulseWidth Section 153
- Remote Functionality 154
- Remote Control Operation 155
- Remote Output Status Events 156
- MX Camera Lens Focusing 157
- Figure C-5: Camera focus ring 165
- Merged Markers 167
- Technical Specifications 169
- MX Camera Specifications 170
- MX40+, MX40 179
- MX Control Specifications 185
- MX Link Specifications 186
- MX Net Specifications 187
- MX Sync Specifications 188
- MX Ultranet Specifications 189
- Regulatory Notices 191
- 9) the appropriate boxes 193
- Medical Devices 194
- Female Male 197
- lb kg 197
- Section C. Device Information 199
- Product Configurations and 203
- Software Options 203
- Troubleshooting 205
- Support Resources 209
- Useful References 210
- Vicon Online Support (VOS) 210
- Documentation Feedback 213
- Customer Satisfaction Survey 215
- Glossary 217
- Aspect ratio 218
- Calibration wand 220
- Capture space 221
- .csm file 223
- Ghost marker 228
- Kinematics 230
- Motorcycle pose 232
- MX F-series Camera 233
- .obj file 235
- RealTime subject 238
- Rotation 239
- Secondary selection 240
- Subject calibration 242
- Trajectory 244
- Virtual point 246
- Walking speed 247
- .xml file 248
- Numerics 249
Relacionado con productos y manuales para Cámaras De Seguridad Vicon IX 2000 L
Cámaras De Seguridad Vicon SVR-PC Manual de usuario
(122 paginas)
(122 paginas)
Cámaras De Seguridad Vicon CE102B Manual de usuario
(12 paginas)
(12 paginas)
Cámaras De Seguridad Vicon SVR-W-O Manual de usuario
(67 paginas)
(67 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales